Inventor(s)

Abstract

This disclosure describes ways for one electric vehicle to draw power through two SAE J1772 (IEC 62196 Type 1)

connectors at the same time, so that the current allowances of two connectors add up. The motivating case is shared or

public Level 2 charging at 240 V or 208 V where the site limits each stall or connector to about 15–20 A, or power-shares

one circuit across several stalls so that a connector advertises a lower pilot duty cycle when neighbouring connectors are in

use. A vehicle that occupies two stalls, or both connectors of a dual-port pedestal, can use both stalls' allocations: for

example 16 A on each connector, 32 A combined. This needs no cooperation from the charging network and never draws

more through either connector than that connector's pilot permits. It does occupy two stalls, and the site's own rules on stall

use apply. Two 120 V receptacles with cord sets are a secondary case. The primary embodiment gives each inlet its own

complete front end: an input filter, rectifier and power-factor-correction stage followed by a galvanically isolated DC-DC

stage, with the two outputs joined only on the high-voltage DC side. No AC conductor of one inlet connects to any

conductor of the other, so each supply equipment's charge-circuit interrupting device (CCID), which trips on about 20 mA

(or 5 mA) of imbalance between outgoing and returning current, sees only balanced current. The disclosure explains why

the isolation is needed: a conventional onboard charger's PFC stage is not isolated and its DC link moves with the AC line,

so paralleling two non-isolated front ends lets current leave through one connector and return through the other. It also

explains the line-frequency leakage through Y-capacitors and how the capacitance is budgeted per inlet. Before either

input relay closes, the controller measures the voltage, frequency and phase angle of each energised inlet and the voltage

between the two inlets' protective-earth pins. It classifies the pair as same leg, opposite legs of a split-phase service, or

different phases of a three-phase supply, uses that as an interlock, and can show the driver which leg each circuit is on.

Control pilot and proximity handling are independent per inlet: each pilot duty cycle sets that inlet's limit, the vehicle

draws up to the sum, and unplugging or faulting one inlet ramps only that inlet down. A load-step test detects two

connectors fed from the same branch circuit, or from a shared neutral, by correlated voltage change, and caps the total.

Form factors include a vehicle with two inlets, an external adapter, and a portable unit fed by two ordinary plug cords. The

preferred adapter passes one input's conductors straight through to its output connector, regenerates the output pilot, and

converts only the other input, through an isolated DC-DC stage and a grid-following inverter that phase-locks to the first

input's voltage and adds its current in parallel downstream of the pass-through point. Each EVSE's CCID stays balanced

because the converted input's current is confined by the transformer and the inverter's current circulates only between the

inverter and the vehicle's charger. If the passed-through supply drops, the inverter stops within a cycle and the output turns

off; if the converted supply drops, the output pilot is first lowered to the passed-through supply's limit and charging

continues. The converter is sized for one input. Either input's pilot may change at any time under the site's load

management; the output pilot follows the sum, and the converted input, which is subordinate, follows the limits set by the

passed-through input's pilot. Two pedestals on different phases of a 208Y/120 V three-phase service are handled because

the inverter locks to the passed-through input's voltage and the converted input is isolated. A two-chain adapter that

converts both inputs, with an AC or DC output, is also described. The disclosure also describes the literal alternative of

combining two 120 V circuits on opposite legs into 240 V, as two-outlet voltage converters do, explains why that defeats a

CCID and the grounding scheme, and describes what it would need (one isolation transformer per input, with

phase-selected polarity). Where the two inlets' AC sides must share a path, as in some adapters, a shared transformer or a

combined non-isolated front end, an alternative embodiment measures each inlet's outgoing-minus-returning current with

an AC- and DC-sensitive sensor and steers it toward zero in closed loop, by per-inlet converter setpoints, return-path

steering, common-mode chokes and, where used, a bounded compensating injection, while an independent earth-leakage

detector that the balancing cannot affect keeps its own trip. Paralleled onboard chargers, dual-inlet vehicles, two-outlet

voltage converters and public discussion of combining two stations are all established. This paper documents arrangements

and operating details. No novelty claim is made.

Keywords: SAE J1772; IEC 62196 Type 1; dual inlet; two EVSE; Level 2; 240 V; 208 V; per-connector current limit;

power sharing; load management; split-phase; three-phase; phase detection; CCID; UL 2231; UL 2594; ground-fault;

residual-current balancing; grid-following inverter; pass-through adapter; Y-capacitor; leakage current; isolated DC-DC;

onboard charger; adapter; cold climate; defensive publication.

Creative Commons License

Creative Commons License
This work is licensed under a Creative Commons Attribution-Share Alike 4.0 License.

Share

COinS