Abstract
This disclosure describes a whole-home refrigerant ecosystem: one central refrigeration plant, on one shared refrigerant
network (or a refrigerant core with secondary loops), that serves every thermal load and every thermal source in and
around a house. It is the house-scale counterpart of a supermarket compressor rack or CO2 (R744) transcritical booster
system with heat reclaim. The cold loads include refrigerators, freezers, ice makers, drinking-water coolers, wine rooms,
cold rooms and dehumidifier evaporators. The warm loads include a staged domestic hot water (DHW) desuperheater and
condenser with cold-inlet preheat, dishwasher water, zoned ducted or ductless indoor heads, central air handlers, hydronic
or boiler loops, pool water, garage and basement heating, sidewalk and driveway snow melting, heated bed pads,
window-perimeter anti-condensation runs, and heated parking pads that warm vehicles before departure, and ovens and
cooking appliances that are refrigerated before cooking, preheated by the heat pump, and actively cooled afterwards so
their stored heat goes to a network load instead of into the kitchen. Computers, servers, miners, network cabinets and
chargers become liquid-cooled heat sources, and deep, blast, ultra-low and walk-in freezers and wine cellars join as add-on
loads at their own suction temperatures. The sources and sinks include a reversible outdoor coil (with the compressor
indoors or packaged outdoors), ground loops (vertical, horizontal, direct-exchange and standing-column), ponds and lakes,
water wells, an indoor pool used as a winter heat source or thermal store, drain water and greywater, and the incoming
cold-water supply line on the branch that serves cold-only fixtures, which can be chilled actively toward 0 °C while it
flows. A supervisory controller ranks sinks and sources by exergy and value (food safety first, then DHW, space heating,
pool, snowmelt, and finally rejection outdoors). It manages thermal storage, demand response and time-of-use operation,
uses reclaimed heat for defrost, manages oil return over a long network, and preserves food-load priority under faults.
Homeowner-connectable branches use self-sealing, pre-charged or pre-evacuated quick-disconnect couplings with
isolation valves and leak detection. Several houses may also share an ambient-temperature water or glycol loop
(fifth-generation district heating and cooling), a ground field, pond, well or seasonal store, with each house joined only
through its own loop-to-loop heat exchanger so that refrigerant never leaves the house and no fluid passes between homes.
Appliances can join through outlet-style wall terminals and power-bar-style splitters carrying suction, hot-gas and liquid
lines, with an electronic expansion valve on every port acting as expansion valve, solenoid and evaporator pressure
regulator, keyed self-sealing couplings, and an open interface through which each appliance describes itself and is granted,
scheduled or refused. Ultrasonic flow meters in every port give a continuous mass balance that locates leaks, meters each
appliance's energy and diagnoses compressors and valves, and a plant pumpdown vessel on load cells weighs the charge.
Operation at −40 °C relies on cascade or booster staging and, above all, on internal, ground and water sources rather than
outdoor air. PV-T panels, flue-gas heat recovery from gas appliances, and stores ranging from stratified tanks and ice to
phase-change materials and borehole seasonal storage also join the network. Heat and energy recovery ventilators gain
network preheat, frost-protection and precooling coils and an exhaust-air evaporator, and clothes dryers and washing
machines draw network heat while their exhaust and drain heat is recovered. Washers and dishwashers give up the heat in
their wash and rinse water before they drain, and dishwashers dry by condensing on a network-cooled surface. Grey water
passes a temperature-selective diverter into a sealed buffer that is part of the sanitary drain, with a mid-tank baffle that
routes it past an extraction coil, and compost bins and piles become a modest low-grade source whose core is kept hot
enough for pathogen kill. Refrigerant choices (CO2, R290 with charge limits and secondary loops, A2L blends) and
protections for ponds, aquifers and potable water are given. Prior art, including the expired distributed household
refrigeration family from 2006 and active heat-reclaim, quick-connect, domestic-water heat pump, thermal-storage, district
thermal-network and kitchen-hood heat-recovery claims, the expired refrigerated-oven patents and products, and
wall-terminal, PV-T, flue-gas, thermal-storage, leak-detection, charge-weighing, compressor-diagnostic, ventilation,
laundry, grey-water, dishwasher and compost art, is acknowledged and described around. Sizing is conceptual. Because
every compressor sits in the plant room, garage or outdoors, the living areas keep only quiet valves and fans, or none with
fanless cabinets, so there is no fridge hum or compressor cycling in kitchens and bedrooms.
Creative Commons License

This work is licensed under a Creative Commons Attribution-Share Alike 4.0 License.
Recommended Citation
Boll, Joe, "A Shared Refrigerant Network for Whole-House Cooling, Heating and Heat Recovery", Technical Disclosure Commons, ()
https://www.tdcommons.org/dpubs_series/13063